HP Workstation Z240 Xeon E3-1225v5 3.3 GHz 8GB RAM 1TB HDD
- Installed RAM memory size :16 GB
- Operating System :Windows 10 Pro
- Brand :HP
- Colour :Black
- Graphics RAM size :2 GB
- CPU speed ;3.7 GHz
HP Workstation Z240 Xeon E3-1225v5 3.3 GHz 8GB RAM 1TB HDD details
System board form factor
ATX 24.38 x 24.38 mm (9.6 x 9.6 in)
Single LGA 1151
CPU bus speed
Intel PCH C236
Memory expansion slots
4 DDR4 memory slots
Memory type supported
DDR4, UDIMM (unbuffered), ECC and non-ECC
Non-Interleaved for single channel. Interleaved when both channels are populated.
Memory speed supported
ECC available on data
4GB, 8GB and 16GB non-ECC/4GB, 8GB and 16GB ECC unbuffered DIMMs are supported. ECC and non-ECC memory DIMMs cannot be mixed on the same system.
PCI express connectors
1 PCI Express Gen3 slot x 1 mechanical/ x 1 electrical (LP, half length)
1 PCI Express Gen3 slot x 16 mechanical/ x 16 electrical (LP, half length)
1 PCI Express Gen3 slot x 1 mechanical/ x 1 electrical (LP, half length)
1 PCI Express Gen3 slot x 16 mechanical/ x 4 electrical (LP, half length)
NOTE: In the PCIe Gen3 (x 16 electrical/x 16 mechanical) slot, if it is not being used for a graphics card, only cards certified as After Market Options for this platform are supported.
Supported drive interfaces
SATA: Integrated (4) Serial ATA interfaces (6 Gb/s SATA). One port can optionally be used for eSATA. RAID 0 and 1 supported. Factory integrated RAID is Microsoft Windows only. RAID 5 is supported by Software XOR.
Serial Attached SCSI: None.
Integrated RAID:NOTE: Requires identical hard drives (speeds, capacity, interface)
Integrated graphics:Intel HD Graphics 530 (on Core i3/i5/i7-6xxx processors); Intel Integrated Graphics for Xeon processors
Based on Unified Memory Architecture (UMA) - a region of system memory is reserved and dedicated to the graphics display.
Support for Microsoft DirectX 11, OpenGL 4.0 and OpenCL 1.2 on Intel HD Graphics P530
3 DP 1.2 graphics ports integrated in motherboard; Supports up to three simultaneous displays across DP outputs. Max resolution supported: 3840 x 2160 at 60Hz
Network Controller: Integrated Ethernet PHY Connection I219LM. Management capabilities: WOL, PXE 2.1 and AMT 9
IDE connector: No
Floppy connector: No
Serial: 1 rear port
2nd Serial: Yes (optional serial port adapter kit required)
Parallel: 1 internal header (optional parallel port adapter required)
HD integrated audio: Yes
Front: 2 USB 3.0, 2 USB 2.0
Rear: 6 USB 3.0
Internal: 1 USB 3.0, 2 USB 2.0
HD integrated audio
Chassis fan header
Front control panel/speaker header
CMOS battery holder - lithium
Integrated trusted platform module
Integrated TPM 1.2.
Power supply headers
Power switch, power LED & hard drive LED header
Clear password jumper
USB or PS/2
Operating voltage range
Rated voltage range
Rated line frequency
Operating line frequency range
Rated input current
4A at 100-240 V
Typical: 444 btu/hr (112 kcal/hr)
Maximum: 890 btu/hr (224 kcal/hr)
Power supply fan
70 mm x 70 mm x 25 mm 4-wire PWM
ENERGY STAR qualified (config dependent)
FEMP standby power compliant
Yes, with wake-on-LAN disabled: <2W in 55 - Power Off
Surge tolerant full ranging power supply (withstands power surges up to 2000 V)
Hood lock header
DrP Lot 6- Tier 2 Compliance at 230 V
Operating: 5° to 35° C (40° to 95° F)
Non-operating: -40° to 60° C (-40° to 140° F)
Operating: 3,000 m (10,000 ft)
Non-operating: 9,100 m (30,000 ft)
Operating: 8% to 85% RH (non-condensing)
Non-operating: 8% to 90%
Operating: 40 g, 2-3 ms, half-sine
Non-operating: 160 cm/s, 2-3 ms, (~100g) Square: 422 cm/s, 20 g
Above 1524 m (5,000 ft) altitude, maximum operating temperature is de-rated by 1° C (1.8° F) per 305 m (1000 ft) elevation increase.
Physical security and serviceability
Includes system board and memory information
Tool-less (internal bays)
Tool-less, except for the processor heatsink
Green user touch points
Yes, on tool-less internal chassis mechanisms
Color-coordinated cables and connectors
Dual color power and HD LED on front of computer
Configuration record SW
Over-temp warning on screen
Restore CD/DVD set
Consists of an operating system DVD (OSDVD) and a driver DVD (DRDVD). OSDVD restores the original operating system. DRDVD will provide all drivers for the system. The DRDVD may also contain applications that originally shipped with the system for optional installation. Applications can also be obtained from HP.com. OSDVD and DRDVD are orderable with the system and available from HP Support.
Dual function front power switch
Yes, causes a fail-safe power off when held for 4 seconds
Yes (optional): Locks side cover and secures chassis from theft
0.22 in diameter padlock loop at rear of system
Cable lock support
Yes, Kensington Cable Lock (optional): Locks side cover and secures chassis from theft 3 x 7 mm slot at rear of system
Universal chassis clamp lock support
Yes (optional): Locks side cover and locks cables to chassis. Secures chassis from theft and allows multiple units to be chained together when used with optional cable Threaded feature at rear of system
Solenoid lock and hood sensor
The Solenoid Hood Lock eliminates the need for a physical key by making the chassis lockable through software and a password. You can also lock and unlock the chassis remotely over the network. The Sensor Kit detects when the access panel has been removed.
Rear port control cover
Yes, locks rear IO cables to prevent cable theft
Serial, parallel, USB, audio, network, enable/disable port control
Yes, enables or disables serial, USB, audio, and network ports
Removable media write/boot control
Yes, prevents ability to boot from removable media on supported devices (and can disable writes to media)
Yes, prevents an unauthorized person from booting up the workstation
Yes, prevents an unauthorized person from changing the workstation configuration
NIC LEDs (integrated) (Green & Amber)
3.3V aux power LED on system PCA
CPUs and heatsinks
A T-15 Torx or flat blade screwdriver is needed to remove the CPU heatsink before the CPU can be removed. CPU removal is tool-less
Power Supply Diagnostic LED
Front power LED
Yes, white (normal), red (fault)
Front hard drive activity LED
Front ODD activity LED
System/emergency ROM flash recovery
Recovers corrupted system BIOS
Air cooled forced convection
Power supply fans
70 x 70 x 25 mm (2.75 x 2.75 x 0.98 in)4-wire PWM (non-serviceable)
CPU heatsink fan
Mainstream (<=65W): 93 x 86 x 75.8 mm (3.66 x 3.38 x 2.98 in)
Performance: (<=95W): 93 x 102.7 x 75.8 mm (3.66 x 4.04 x 2.98 in)
CPU heatsink fan also operates as the chassis fan.
Memory heatsink fan
HP PC Hardware Diagnostics UEFI
HP PC Hardware Diagnostics (UEFI) enables hardware level testing outside the operating system on many components. The diagnostics can be invoked by pressing F2 at POST, and is available as a download from HP Support.
Access panel key lock
Advanced Configuration and Power Management Interface (ACPI). Allows the system to wake from a low power mode and controls system power consumption, making it possible to place individual cards and peripherals in a low-power or powered-off state without affecting other elements of the system
Trusted platform module chip
Integrated chassis handles
Requires T15 Torx or flat blade screwdriver
PCI card retention
Yes, rear (all), middle (none), front (none)
CMOS battery holder
Diagnostic power switch LED on board
Clear password jumper
Clear CMOS button
BIOS 32-bit services
Standard BIOS 32-bit Service Directory Proposal v0.4
PCI 3.0 support
Full BIOS support for PCI Express through industry standard interfaces..
ATAPI Removable Media Device BIOS Specification Version 1.0.
BIOS Boot Specification v1.01.
Provides more control over how and from what devices the workstation will boot.
WMI is Microsoft's implementation of Web-Based Enterprise Management (WBEM) for Windows. WMI is fully compliant with the Distributed Management Task Force (DMTF) Common Information Model (CIM) and WBEM specifications.
BIOS power on
Users can define a specific day-of-week and time for the system to power on.
ROM Based Computer Setup Utility (F10)
Review and customize system configuration settings controlled by the BIOS
System/emergency ROM flash recovery with video
Recovers system BIOS in corrupted Flash ROM
Saves BIOS settings to USB flash device in human readable file. Repset.exe utility can then replicate these settings on machines being deployed without entering Computer Configuration Utility (F10 Setup)
System Management BIOS 2.7.1, for system management information
Disables the ability to boot from removable media on supported devices
Memory change alert
Alerts management console if memory is removed or changed
Monitors the temperature state within the chassis.
NORMAL - normal temperature ranges
ALERTED - excessive temperatures are detected, raises a flag so action can be taken to avoid shutdown or provide for a smoother system shutdown.
SHUTDOWN - excessive temperatures are encountered. Automatically shuts down the computer without warning before hardware component damage occurs.
Remote ROM flash
Provides secure, fail-safe ROM image management from a central network console.
Updates can be performed before starting the OS. Updates can be periodically scheduled.
ACPI (Advanced Configuration and Power Management Interface)
Allows the system to enter and resume from low power modes (sleep states). Enables an operating system to control system power consumption based on the dynamic workload.
Makes it possible to place individual cards and peripherals in a low-power or powered-off state without affecting other elements of the system. Supports ACPI 4.0 for full compatibility with 64-bit operating systems.
A user-defined string stored in non-volatile memory that is displayed in the BIOS splash screen.
Remote Wakeup/Remote Shutdown
System administrators can power on, restart, and power off a client computer
ASF 2.0 Compliant
Instantly Available PC (Suspend to RAM - ACPI sleep state S3)
Allows for very low power consumption with quick resume time
Remote System Installation via F12 (PXE 2.1) (Remote Boot from Server)
Allows a new or existing system to boot over the network and download software, including the operating system
ROM revision levels
Reports the system BIOS revision level in Computer Configuration Utility (F10 Setup). Version is available through an industry standard interface (SMBIOS) so that management SW applications can use and report this information
System board revision level
Allows management SW to read revision level of the system board. Revision level is digitally encoded into the HW and cannot be modified
Start-up Diagnostics (Power-on Self-Test)
Assesses system health at boot time with selectable levels of testing.
Auto Setup when new hardware installed
System automatically detects addition of new hardware.
The system can be booted without a keyboard.
Localized ROM Setup
Common BIOS image supports System Configuration Utility (F10 Setup) menus in 12 languages with local keyboard mappings.
The user or IT administrator to set a unique tag string in non-volatile memory.
Allows I/O slot parameters (option ROM enable/disable) to be configured individually.
Control parameters are set according to detected hardware configuration for optimal acoustics.
(Pre-video) critical errors are reported via beeps and blinks on the power LED.
Intel Active Management Technology (AMT)
AMT 11.0; Allows workstation status to be monitored on a remote console
Digitally and Cryptographically Signed BIOS
Helps to prevent the installation of unauthorized versions of a BIOS (a rogue BIOS) from a virus, malware, or other code that could lead to compromised system security, data access, physical service, or even system board replacement.
Master Boot Record Protection
A feature in the HP BIOS that prevents changes and/or infections to the Master Boot Record. Useful in protecting from viruses.
Boot Block Emergency Recovery Mode (BIOS Recovery)
The HP BIOS offers a write-protected boot block ROM that provides recovery from a failed flashing of the computer BIOS. This special recovery mode prevents the system from becoming unusable or “bricked” when a BIOS update is interrupted.
Revision Supported by the BIOS
UEFI specification revision
Advanced Configuration and Power Management Interface, Version 4.0
Alert Standard Format Specification, Version 2.0
AT Attachment 6 with Packet Interface (ATA/ATAPI-6), Revision 3b
"El Torito" Bootable CD-ROM Format Specification Version 1.0
Enhanced Disk Drive Specification Version 1.1
BIOS Enhanced Disk Drive Specification Version 3.0
PCI Express Base Specification, Revision 2.0
PCI Express Base Specification, Revision 3.0.
POST Memory Manager Specification, Version 1.01
Serial ATA II: Extensions to Serial ATA 1.0, Revision 1.0a
Serial ATA II Cables and Connectors Volume 2 Gold
SATA-IO SATA Revision 3.0 Specification
Serial ATA Specification, Revision 1.0a
PC SDRAM Serial Presence Detect (SPD) Specification, Revision 1.2B
Trusted Computing Group TPM Specification Version 1.2 (TPM 2.0 via Firmware Update)
Universal Serial Bus Revision 1.1 Specification
Universal Serial Bus Revision 2.0 Specification
Universal Serial Bus Revision 3.0 Specification
Intel Active Management Technology (AMT)
An advanced set of remote management features and functionality which provides network administrators the latest and most effective tools to remotely discover, heal, and protect networked client systems regardless of the system's health or power state. AMT 11.0 includes the following advanced management functions:
Power Management (on, off, standby, reset)
Hardware/Software Inventory (includes BIOS and firmware revisions
System Defense Filters
SOL (Serial Over LAN)
DASH 1.1 compliance
Fast Call for Help - a client inside or outside the firewall may initiate a call for help via BIOS screen, periodic connections, or alert triggered connection
Remote Scheduled Maintenance - pre-schedule when the PC connects to the IT or service provider console for maintenance. Remote PCs can get required patches, be inventoried, etc by connecting to their IT console or Service Provider when it's convenient
Remote Alerts - automatically alert IT or service provider if issues arise
Access Monitor - Provides oversight into Intel AMT actions to support security requirements
PC Alarm Clock
Protected Audio Video Path (PAVP)
Microsoft NAP Support
Host Base set-up and configuration
Management Engine (ME) firmware roll back
Enhanced KVM resolution (Up to 4K)
Intel vPro technology
The HP Z240 workstations support Intel vPro technology when purchased with a vPro technology capable CPU: Intel Xeon processor family or 6th Generation Intel Core i5/i7 processors with Intel VT-d/VT-x and Intel TXT technology
Service, support, and warranty
Program to proactively communicate Product Change Notifications (PCNs) and Customer Advisories by email to customers, based on a user-defined profile.
PCNs provide advance notification of hardware and software changes to be implemented in the factory providing time to plan for transition.
Customer Advisories provide concise, effective problem resolution, greatly reducing the need to call technical support.
Intel CoreTM i7-6700 3.4 2133 4C CPU
Intel CoreTM i7-6600 3.3 2133 4C CPU
Intel CoreTM i7-6500 3.2 2133 4C CPU
500 GB SATA 7200 rpm 6 Gb/s 3.5 in HDD
1 TB SATA 7200 rpm 6 Gb/s 3.5 in HDD
2 TB SATA 7200 rpm 6 Gb/s 3.5 in HDD
3 TB SATA 7200 rpm 6 Gb/s 3.5 in HDD
500 GB SATA 7.2 K SED SFF HDD
1 TB SATA 7200 rpm 8 Gb/s 3.5 in SSHD (hybrid)
128 GB SATA 6 Gb/s SSD
HP 256GB SATA 6Gb/s SSD
HP 512 GB SATA 6Gb/s SSD
HP 1 TB SATA 6Gb/s SSD
HP 256GB SATA 6Gb/s SED SSD
PCIe SSDs for HP workstations
HP Z turbo drive G2 128 GB SSD
HP Z turbo drive G2 256 GB SSD
HP Z turbo drive G2 512 GB SSD
Integrated Intel HD Graphics
NVIDIA NVS 310 512 MB graphics
NVIDIA NVS 315 1 GB Graphics
NVIDIA NVS 510 2 GB graphics
AMD FirePro W2100 2 GB
NVIDIA Quadro K420 1 GB Graphics
NVIDIA Quadro K620 2 GB Graphics
NVIDIA Quadro K1200 4GB Graphics
Optical and removable storage
HP SD media card reader
HP Thunderbolt 2 PCIe 1-port I/O card
Networking and communications
Integrated Intel I217LM PCIe GbE Controller (Intel vPro with Intel AMT 11.0)
Supported drive interfaces
Integrated (5) Serial ATA interfaces (6 Gb/s SATA). One port can optionally be used for eSATA.
RAID 0 and 1 supported. Factory integrated RAID is Microsoft Windows only.
Intel HD Graphics 530 (on Core i3/i5/i7-6xxx processors)
Intel Integrated Graphics for Xeon E3 processors
Based on Unified Memory Architecture (UMA) - A region of system memory is reserved and dedicated to the graphics display.
Support for Microsoft DirectX 11, OpenGL 4.0 and OpenCL 1.2 on Intel HD Graphics P530;.
Supports up to three simultaneous displays across DP outputs.
Max. resolution supported: 3840 x 2160 at 60Hz
Integrated Ethernet PHY Connection I217LM. Management capabilities: WOL, PXE 2.1 and AMT 11.0
Dimensions (W x H x D)
100 x 338 x 381 mm (3.95 x 13.3 x 15 in)
Social and environmental
Eco-Label Certifications and Declarations
This product is low halogen except for power cords, cables and peripherals. Service parts obtained after purchase may not be Low Halogen.
ENERGY STAR (energy-saving features available on selected configurations -Windows only)
US Federal Energy Management Program (FEMP)
China Energy Conservation Program (CECP)
IT ECO declaration
The battery in this product complies with EU Directive 2006/66/EC
Battery size: CR2032 (coin cell)
Battery type: Lithium Metal
The battery in this product does not contain:
Mercury greater than 5ppm by weight
Cadmium greater than 10ppm by weight
Lead greater than 40ppm by weight
Restricted material usage
Restricted Material Usage This product meets the material restrictions specified in HP's General Specification for the Environment. HP is committed to compliance with all applicable environmental laws and regulations, including the European Union Restriction of Hazardous Substances (RoHS) Directive. HP's goal is to exceed compliance obligations by meeting the requirements of the RoHS Directive on a worldwide basis.
Low halogen statement
This product is low halogen except for power cords, cables and peripherals, as well as the following customer-configurable internal components: Creative Recon3D PCIe Audio Card is not Low Halogen. Service parts obtained after purchase may not be Low Halogen.
End-of-Life management and recycling
HP offers end-of-life HP product return and recycling programs in many geographic areas. To recycle your product, please go to: http://www.hp.com/recycle or contact your nearest HP sales office. Products returned to HP will be recycled, recovered or disposed of in a responsible manner. This product is greater than 90% recyclable by weight when properly disposed of at end of life.
This HP product is designed to comply with the Waste Electrical and Electronic Equipment (WEEE) Directive - 2002/96/EC.
Plastic parts weighing over 25 grams used in the product are marked per ISO 11469 and ISO1043.
This product is >90% recycle-able when properly disposed of at end of life
EPEAT Gold registered in the U.S. EPEAT registration varies by country.
HP Workstation product packaging meets the HP General Specification
Does not contain restricted substances listed in HP Standard 011-1 General Specification for the Environment
Does not contain ozone-depleting substances (ODS)
Does not contain heavy metals (lead, mercury, cadmium or hexavalent chromium) in excess of 100 ppm sum total for all heavy metals listed
Maximizes the use of post-consumer recycled content materials in packaging materials
All packaging material is recyclable
All packaging material is designed for ease of disassembly
Reduced size and weight of packages to improve transportation fuel efficiency
Plastic packaging materials are marked according to ISO 11469 and DIN 6120 standards formatting
Cushions made from fabricated recycled expanded-polyethylene (EPE) or recycled expanded-polypropylene (EPP). May also be made from recycled molded paper-pulp (MPP).
Carton made from corrugated fiberboard with at least 25% recycled content.
Cash Payments (Nairobi only)
We accept Cash Payments . This is applicable for Pay on Delivery orders within Nairobi Metropolitan area.
- Go to Safaricom SIM Tool Kit, select M-PESA menu, select “Lipa na M-PESA“
- Select “Pay Bill“
- Select “Enter Business no.“, Enter Rondamo technologies Lipa na M-PESA PayBill Number 964586 and press “OK”
- Account no. ( Indicate Order No. & Your Name)
- “Enter Amount : ( Total shown on Invoice)
- Enter your M-PESA PIN and press “OK”
This is applicable for all orders, both in Nairobi & upcountry besides large orders over Ksh 250,000/-
Bank Deposit /EFT
You can deposit payment for your order directly into our Stanbic bank account. We check our bank account for new payments every day but depending on your bank it can take 1–2 business days for your payment to appear. To ensure that we can reconcile your payment quickly please make sure you follow the instructions carefully and include a reference with your payment.
You can deposit payment for your order directly into our Stanbic bank account via Pesalink. all products are eligible for payment via Pesalink. To ensure that we can reconcile your payment quickly please make sure you follow the instructions carefully and include a reference with your payment.
Warranty Info (3 months)
The warranty tendered hereunder, on the electronic product(s) sold under this invoice will be provided exclusively by Rondamo Technologies and are limited to 3 Months from the date of this invoice, except otherwise mentioned as per the warranty conditions as carried along with the products(s) or mentioned on Rondamo Technologies Invoice.
The warranty is Return to Base .
Accurate delivery estimates are displayed on the product page and in the Checkout before you confirm your order.
Delivery estimates take into consideration both the delivery address and the types of products being ordered.
The remainder of this article discusses delivery times in more general terms.
Same Day Delivery / For Customers in Nairobi Metropolitan Area
We use Courier for these orders, which allows fast and reliable delivery to destinations across their comprehensive domestic network. Orders placed between 7 Am and 5 Pm will be delivered the same day otherwise they will be delivered the following day. Delivery times vary depending on a product's stock status and the intended delivery address. For very large orders, we may be forced to use Mainfreight as these orders lie outside of what Courier Rider services can handle. If your order is being shipped with Mainfreight, this will be indicated in your fulfilment email along with a tracking number.
Most In stock products are delivered overnight anywhere in Kenya – provided the order is placed before the advertised cut-off time. Our Overnight Delivery cut-off is usually 4:30pm Monday to Friday, however, this is updated daily and the expected shipping date will be shown for you on the product page. Larger products take an additional 1–2 days to be delivered.
Evening Express Delivery
Same Day Delivery is available to Nairobi & its suburbs. Same Day Delivery orders are delivered between 4pm and 7pm in the evening on the same day your order is dispatched.
If you are ordering on a business day and before the cutoff time, the option will be called “Same Day Delivery”. If you are ordering after the cutoff time or on a weekend or public holiday, the option will be called “Evening Express Delivery”. And May incur extra Costs other than the standard shipping fee.